Advanced Medical Equipment

Spread the Care & Hospitality

		Equipment & Furniture Component
	LIST OF MEDICAL EQUIPMENT

Item	Name	Quantity	Technical Specifications and Standards
No

			Processing machine for X-ray films from 13×18 cm. 18×24 cm.24×30
			cm.30x40cm.35.6×35.6 cm. 35x43cm.
			Capacity at least 60 films per hour
	X-Ray Film processor		Standard Equipment: Processor + set of 3 replenish bottles
1	X-Ray Film processor		Accessories: Water supply connection with shut-off valve , Filter , Light-tight
1	Table top
	Table top	1	cover , Processor stand
		1	cover , Processor stand
			Automatic stand-by mode.
			Automatic film detection
			Power Requirements :
			220 VAC ±10 % 50 Hz .

			X-ray Film Illuminator (Viewer) . 2 Fields . Wall-Mount
			Diffuse, uniform, flicker free illumination
			Transparent Spring-loaded film Retainers shall grip lightly and firmly without
			obscuring top edge details
			Screen shall be recessed into the cabinet to help keep the interior dust free and
			eliminate side light spill
			The film retainers shall always operate effectively maintaining an even pressure
2	X-ray Film Viewer		across the full width of the illuminator.
2	X-ray Film Viewer		Direct Starting , Luminous Source : Daylight
			Direct Starting , Luminous Source : Daylight
			Command and Control on Front Side.
			Bipolar Switch with Pilot lamp
			Wall Fixations shall be provided for . Cord , Local Plug
		8	Power Supply : 220V/50Hz
			CE;
			EC Marked
			US FDA;
			ISO certification
			Universal, Remote controlled Universal Unit
			Processor controlled, Mixed Cassette’s Radiography and Digital Fluoroscopy
			screening System.
			Overhead Tube on the freely moving Tube Arm without floor mounted column.
			The System to be suitable for Standard Skeletal and Radiographic Examinations,
			Including Lateral Exposures and Oblique Beam Projections
			Fully Automatic Under Table Spot Film Device for Cassette Radiography with
		1	Extensive Range of Cassettes, Grids and Attachments for Image Intensifier.
			Free Cassette Exposures on Table, Floor, Wheelchair or Gurney.
			Table.
			Tilt: Motor Driven, +90º to -15º, automatic stop in horizontal position
			Height: approximately 85 cm.
			Tabletop Outside Dimensions: length approximately 200cm,Width approximately
			80cm
3	X-Ray Unit Universal		Radiolucent: not less than 190cm x 55cm.
			Longitudinal Travel: Motor Driven, at least 160 cm
			Transverse Travel: at least 20 cm
			Patient Weight: at least 200 kg.
			Tube Assembly.
			Max. exposure voltage : 150 kV
			Anode heat dissipation rate at least 30 kW for small focus and 60 kW for large
			focus
			Anode heat storage capacity at least 500 kHU
			Dual focus 0.6 mm and 1 mm
			Complete filtration W ≥ 2.5 mm Al
			Focus-Film Distance (SID) Fixed Variable : 115cm / 150cm. 115cm and 150cm
			must be set by Motor Driven with Adjustment Speed
			Oblique Projections: max.-40º-+40º ( SID 115cm.) and -35º-+35º (SID 150cm),
			Automatic Parallax Compensation Between Cassette and Image Intensifier Input
			Screen in Central Ray.

page 1 of 27

Equipment & Furniture Component

Tube Assembly Swivel: Manually in the Range +90º to -90º with Stops max. every 10º and -90º to 180º with stops max. every 30º.

Spot Film Device.

Front loading, automatically drawing in and out, centering and format sensing for

Cassettes, of the Formats 18x24cm (8″x10″) to 35 x 43cm (14″x17″), Standardized

According to IEC, ANSI and DIN

Automatic Format Collimation: must be Selected Separately According to Format

Height/Width for Cassette Spot filming; Automatic Formatting for Bucky

Exposures, Object-related Collimation.

Film Segmentation: Minimum 4 on 1., in Multiple Segmentation According to

Cassettes Program

Inward Movement Time: Park to Exposure position not more than 1sec.

Time Interval: Fluoroscopy/Radiography ≤1.0 sec. without grid movement.

Scattered Radiation Grid: Stationary 17:1, 70 Lines/cm, Fo=125cm.,

Excursion: minimum 105cm, Remote-controlled.

Compression Device.

Radio transparent, Remotely Controlled, Detachable and Replaceable Cone minimum 3 Shapes.

Compression Force range: from 5 to 155N, Movement Blockage starting from 50N Force Indication: Digital at the System Remote Control Console.

Projection Angle: -30º-+30º.

Image Intensifier and TV System

3 Image Fields 13 to 23 cm

Visual resolution: Mean Value 5.2; 5.8; 6.4 Lp/mm

Television System Standard: Line Frequency 50Hz; 625 Lines with 50Hz. TV Technology : CCD sensor, noise suppression, LIH function Automatic Dose Stabilization (ADR)

Monitor: 44cm or more, Frame Rate at least 50 Hz.

X-Ray Generator

High Frequency, Multipulse Up to 150 kV, ≥50kW.

Automatic System: 1-Point Technique with Continuously Falling Load; 2 -,3- Point Technique with Constant Load; 3-Point Technique with AEC

Organ Programs: minimum 20 Organ Programs must be generated and stored. Number of Workstations: not less than 5 of with 1 Fluoroscopic Workstation Fluoroscopy working range: minimum 40kV/ 0.5mA up to maximum 110kV≤10mA.

Fluoroscopic Mode Selectable: Fluoroscopy Under Manual Control / Automatic Control

Fluoroscopy Under Manual Control: manual select kV but mA must be calculated from Anti-isowatt, curve

Fluoroscopy Under Automatic Control: Minimum 2 required Characteristic Curve must be selected for Automatic Dose Rate Control : us Minimal Dose/ Contrast Litho ( or other according customer ordering)

Tube Connection: minimum 2 Double-Focus Tube Assembly. 3 field Automatic Exposure Control

Primary Collimator: Inherent Filtration 1.0mm Al; additional Filters 0.1mm Cu, 0.2mm Cu, 0.3mm Cu.

Ambient Conditions

Operation: +10Cº to 35Cº; 20% to 75% relative humidity, non-condensing; 70kPa to 106kPa

Storage and Transport: -20Cº to+70Cº; 10% to 95% relative humidity, non-condensing; 70kPa to 106kPa

Power Connection

Nominal Voltage: 3/N/PE, 380V±10%

Nominal Frequency: 50Hz.

Completeness:

Lead glass, radiation protection window 80x100cm. ±10 % , 2,1 Pb equiv X-ray protection:

1x Coat apron, 0.35 Pb, size medium, 110cm. X-ray protection coat apron for general examinations.

1x Gonad protection apron 40x37cm, 0.5 Pb. Apron for adults for protection of ovarian and gonad.

1x Gonad protection capsule for boys, 1.0 Pb.

Set of cassettes
Cassette without patient ID window
Fitted with green screen

2x Cassette with green screen, 18 cm x 24 cm

page 2 of 27

		Equipment & Furniture Component

			1x Cassette with green screen, 18 cam 43 cm
			2x Cassette with green screen, 24 cm x 30 cm
			2x Cassette with green screen, 35 cm x 43 cm
			1x Cassette with green screen, 35 cm x 35 cm
			Exposure range at least 0.5–200 mAs
			Shortest exposure time: not more than 10ms.
			Max. exposure time: not less than 5 sec.
			Tube head must be rotatable in all planes.
			Adjustable collimator and light marker Easy to use and to move. Non automotive
			Two point technique – kV and mAs.
			High- frequency X-ray generator with multipulse voltage provider.
4	X-Ray Mobile	1	The touch-screen keys and digital display of kV and mAs values.
			Output: not less than 2.5kW. 120 kV, 40mA.
			Focal spot not more than 1 mm.
			Collimator: rotatable ± 90°
			Max. horizontal extension at least 800mm
			Power Requirements
			220 V ±10%, 50Hz
			Wide Dynamic Range Digital Front-end
			The 12-bit A/D converter
			Multi-beam processing.
			Image Display Modes
			B: gray-scale imaging, M,D: Spectral Doppler (PW,HPRF PW),
			Flow: Color Doppler and Power Flow imaging, Dual B, B and M, B and D, B(Flow),
			Dual B (Flow), M(Flow), B(Flow) and M(Flow), B(Flow) and D,
			Triplex mode: B, Flow and PW Doppler simultaneous real-time display,
			Dual Dynamic Display (DDD): B and B (Flow) simultaneous real-time display, TDI
			(Tissue Doppler Imaging)-Available on electronic scanning probes.
			Request function: In multi-mode display, it is possible to select one image for full
			screen display.
			DMS (Integrated Data Management System)
		1	Measurement and Analysis.
			General measurements
			On B-mode image
			On M-mode image
			On spectral Doppler
			On B/D-mode image
			On B(Fiow) mode image
			Obstétrical measurements & calculations
5	Ultrasound (3 probes)		Gynecological measurements & calculations
5	Ultrasound (3 probes)		Peripheral vessels analysis
			Peripheral vessels analysis
			Urological measurements & calculations
			Abdominal measurements
			Report Functions
			Data Communication Function
			Preset Function
			Characters and graphic displays
			Probe connectors
			Standard
			Active connectors: 2 connectors
			Dummy connector for rest: 1 connector
			Viewing Monitor
			15-inch diagonal color Liquid Crystal Display with brightness and contrast controls
			Acoustic Power
			0 to 100%, changeable
			Environmental Requirements
			Temperature: +10 to +40 degrees C
			Relative Humidity: 30 to 75%
			Power Requirements: 220V / 50 Hz.
			Probes
			General abdomen OB/GYN 2.5-6.0 MHz.
			Small parts, PV (steered linear) 5.0-10.0 MHz.
			Adult heart (harmonic echo) 2.1-3.8 MHz.
6	Gastroscope (With halogen		Optical System :
6	light source)		Field of view: at least 100°°
	light source)		Field of view: at least 100°°
			Depth of field: at least 4 to 100 mm

page 3 of 27

Equipment & Furniture Component

			Distal end : Outer diameter: not more than 10mm.
			Bending Section
			Range of tip bending: not less than Up 210°, Down 90°, Right 100°, Left 100°
			Insertion tube : Outer diameter: not more than 13.3mm
			Working length: not less than 1025mm.
			Length markings
			Instrument channel :
			Inner diameter: not less than 2.8mm.
			Light source
			Halogen technology shall provide a high light intensity of at least 150W.
			Variable light intensity.
			Fast and easy bulb change during operation : In case of a bulb failure immediate
		1	switch to the second bulb with the reverser shall be possible.Adjustment of
			brightness and power with buttons and switches on the front panel.
			Shall be connectable with conventional telescopes, fiberscope.
			Shall be adaptable to all endoscopic procedures
			Optionally , an automatic built-in swivel mechanism will bring the spare halogen
			bulb into working position.
			Technical Data : Halogen , 150 watts , Halogen, 2 pieces
			Manual switch , 2 x 150 W , 24 V
			Power Supply : 220 VAC 50 Hz .
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Optical System :
			Field of view: at least 120°
			Depth of field: 5 –÷100 mm.
			Distal end : Outer diameter: not more than 13mm.
			Bending Section
		1	Range of tip bending: not less than Up 180°, Down 180°, Right 160°, Left 160°
			Insertion tube : Outer diameter: not more than 13.3mm
			Working length: not less than 1680mm.
			Instrument channel
			Inner diameter: not less than 3.2mm.
			Light Source
			Halogen technology shall provide a high light intensity of at least 150W .
			Variable light intensity
	Colonoscope		Fast and easy bulb change during operation : In case of a bulb failure immediate
7	(With halogen light		switch to the second bulb with the reverser shall be possible
7	(With halogen light
	source)		Adjustment of brightness and power with buttons and switches on the front panel.
			Shall be connectable with conventional telescopes, fiberscope,
			Shall be adaptable to all endoscopic procedures
			Optionally , an automatic built-in swivel mechanism will bring the spare halogen
			bulb into working position.
			Technical Data : Halogen , 150 watts , Halogen, 2 pieces
			Manual switch , 2 x 150 W ,24 V
			Power Supply : 220 VAC 50Hz .
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

page 4 of 27

		Equipment & Furniture Component

			Recording ECG Leads: 12 standard Leads
			Recording Channels: 3/1 user selectable
			LCD display of ECG
			Lead switching: manual and automatic.
			Sensitivity, mm/mV: 5, 10, 20.
			Calibration signal: automatic and manual.
			Diagnostic frequency range 0.67–150 Hz or better
			Filters for mains frequency, low frequency, muscle artefact, high frequency
			Recorder:
			Recording method: thermal paper
			Recording speed, mm/sec: 25/ 50 user selectable
			Channels acquired simultaneously:1/ 3 user selectable
			Channels printed simultaneously:1/ 3 user selectable
			Other features:
			Portable
		3	Mains and internal rechargeable battery operation
	Electrocardiograph 3	3	Battery operating time, minimum: 90 min.
8			Battery operating time, minimum: 90 min.
			Power requirements: 220 V, 50 Hz
	channels		Power requirements: 220 V, 50 Hz
	channels
			Accessories:
			1. Patient cable
			2. 6 chest limb electrodes
			3. 4 limb electrodes
			4. 4 strap electrodes
			5.
			6. 1 bottle ECG Gel
			7. 2 rolls of paper or Z-Fold
			8. Carry bag
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

		3	Surgical Lighthead with five Projectors , Ceiling Suspended
			Light intensity (Ec) at least150 000 lx
			Color rendering index (general) Ra 96
			Color rendering index (red) R9 89
			Light field size 15 – 30 cm.
			Colour temperature 4200º Kelvin
			Working range without focusing approximately 70 – 140 cm
			Power supply 220 VAC, 50 Hz
			Adjustable light intensity
			Power Supply , 220V/50 Hz.
	Operating theatre light (5		Power Stabilizer shall be supplied
9	Operating theatre light (5		This equipment shall be supplied with all necessary fixation gears to the Building
9	spotlights)
	spotlights)		structure
			structure
			Replacement Bulbs (5) and Sterilizable Handles (5) shall be supplied
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification
			Accessories/Spares :
			5 Bulbs per unit
			2 Handles per unit
			Operating table designed for carrying out treatments, dressing interventions and
	Operating Table		operations of general surgery and traumatology
10	(Trauma/Multifunction,		All exposed metallic parts shall be made from stainless, acid proof steel.
10	(Trauma/Multifunction,		The table base shall be mobile and shall have central brakes
	electric/hydraulic driven
	electric/hydraulic driven		Back rest and leg rest inclination angle, kidney elevator, Trendelenburg and
			reverse-Trendelenburg positions and height adjustment of the table top shall be

page 5 of 27

Equipment & Furniture Component

		activated by electro – hydraulic system
		The table top shall be translucent for x-rays with 5 separate Sections
		Table top length approximately 2000 mm
		Table top width approximately 600mm
		Minimal height of the table 750mm
		Maximal height of the table 1100mm indicatively
		Trendelenburg at least 25
		Reverse Trendelenburg at least 25º
		Lateral tilt at least 18º
		Back rest inclination angle at least +55º to -25º
		Head rest inclination angle at least 45º up
		Head rest inclination angle at least 20º down
		Power requirements
		220 VAC ±10 % , 50Hz
	1	Accessories:
		Anaesthetic Screen with clamp with telescopic tubes : 1
		Body restraint Strap with clamp : 1
		Padded Shoulder supports : 2
		Padded Leg support with swivel type clamp : 2
		Padded arm Rests 450 -500 mm long with two arm Clamps : 2
		Padded Lateral support with universal attachment Clamp : 2
		Padded rubber mattresses with Anti Microbial agent incorporated into all components
		that assists in Prohibiting growth of bacteria & fungi and easy to clean and maintain
		and of at least of 1” thickness : 2 X5 Sections
		Head rest , I.V drip Stands attachable to the table
		Environmental factors:
		The unit shall be capable of being stored continuously in ambient temperature of 0 –
		50deg C and relative humidity of 15-90%
		The unit shall be capable of operating continuously in ambient temperature of 10 -40
		deg C and relative humidity of 15-90%
		Accessory for traumatology are optional and shall be listed separately
		Standards
		CE;
		EC Marked
		US FDA;
		ISO certification
		Operating table for carrying out treatments, dressing interventions and operations
		of general surgery (3-4 surgeries daily).
		All exposed metallic parts shall be made from stainless, acid proof steel.
		The table base shall be mobile and shall have central brakes
		Back rest and leg rest inclination angle, Trendelenburg and reverse-
		Trendelenburg positions and height adjustment of the table top shall be activated
		by electro – hydraulic system
		The table top shall be translucent for x-rays with 5 separate Sections
		Table top length approximately 2000 mmTable top width approximately 600mm
		Minimal height of the table 750mm
		Maximal height of the table 1100mm indicatively
		Trendelenburg at least 25º
		Reverse Trendelenburg at least 25º
		Lateral tilt at least 18º
	Operating Table	Back rest inclination angle at least +55º to -25º
11	(Multifunction,	Head rest inclination angle at least 45º up
11	(Multifunction,	Head rest inclination angle at least 20º down
	electric/hydraulic driven)	Head rest inclination angle at least 20º down
	electric/hydraulic driven)

Power requirements

220 VAC ±10 % , 50Hz Accessories:

Anaesthetic Screen with clamp with telescopic tubes : 1 Body restraint Strap with clamp : 1

Padded Shoulder supports : 2

Padded Leg support with swivel type clamp : 2

Padded arm Rests 450 -500 mm long with two arm Clamps : 2 Padded Lateral support with universal attachment Clamp : 2

Padded rubber mattresses with Anti Microbial agent incorporated into all components that assists in Prohibiting growth of bacteria & fungi and easy to clean and maintain and of at least of 1” thickness : 2 X5 Sections

Head rest , I.V drip Stands attachable to the table Environmental factors:

page 6 of 27

Equipment & Furniture Component

			The unit shall be capable of being stored continuously in ambient temperature of 0 –
			50deg C and relative humidity of 15-90%
			The unit shall be capable of operating continuously in ambient temperature of 10 -40
			deg C and relative humidity of 15-90%
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Anesthesia Machine used for delivering anesthesia Agents to Patient during Surgery
			Procedures. The complete set-up shall also ventilate the Patient
			Patient monitoring system ECG, EtCO_2, Pulse Oximeter and airway pressure, NIBP,
			rectal/&skin Temperature.
			The full System shall be completed with :
			Anaesthesia gas delivery system, O2/N2O/Compressed Air .
			Circle absorber system.
			Precision vaporiser for halothane
			Anaesthesia ventilator
			Patient Circuit
			Anesthesia gas delivery system:
		3	Shall have provision for delivery of oxygen, nitrous oxide and medical air with
			pressure gauges.
			Oxygen and Nitrous oxide should be linked either mechanically or pneumatically to
			ensure a minimum of 25% oxygen delivery at all times to avoid delivery of hypoxic
			mixture.
			Shall have audio-visual oxygen Failure Warning System with Nitrous oxide cut off.
			Shall have back bar ISO pin type to attach Vaporizer easily.
			Flowmeter oxygen : 0÷2; 2÷10 litres/min, minimum range
			Flowmeter N2O : 0÷2; 2÷10 litres/min, minimum range with safety mechanism
			(hypoxic link) or similar
			Flowmeter , Medical Air 0÷10 litres/min.
			Shall be supplied with necessary Attachments for use of the breathing Circuits
			(Ruben , Bains, Jackson-Rees or Magill )
			Construction :
			Shall have top Shelf to keep monitors and a Tabletop with Drawers to keep
			anaesthetic drugs, equipments etc.
	Anesthesia trolley		Castor wheels should be durable , moisture resistant and antistatic
	Anesthesia trolley		The Anaesthesia machine frame shall be made of rust proof material/Stainless steel
12	(anesthesia machine with
12	(anesthesia machine with		or sheet Steel protected with Epoxy-Paint
	ventilator and monitor)		or sheet Steel protected with Epoxy-Paint
	ventilator and monitor)		Standard Circle Absorber System
			Standard Circle Absorber System
			Shall have adjustable pressure limiting Valve, breathing circuit pressure measuring
			device.
			Shall have a Bag/Ventilator selecting Valve integrated onto the Absorber.
			Facility to attach oxygen sensor
			Shall have CO2 absorbent Chamber Canister (Soda Lime )
			Precision Vaporizers (Temperature, Pressure and Flow compensated) for Halothane
			Should be easy to mount and dismount from the back bar.
			Vaporisers shall have ISO pin type (Selectatec) Mounting and Vaporiser interlocking
			facility
			Shall have a standard filling port with keyed filling device
			Should be designed for transport with liquid in Vaporiser Chamber with protection
			against tipping and shaking
			Maintenance free Vaporiser
			Ventilator
			Shall be a bag in bottle anaesthesia Ventilator with standing (ascending/Piston)
			Bellows
			Shall be supplied with adult and paediatric Bellows
			Shall be able to set Tidal Volume, Respiratory rate and I:E ratio
			Ventilator should have audible alarms for ventilator failure, low oxygen supply
			Pressure, inadequate volume delivery, disconnection alarm, and power supply failure.
			Ventilation mode: CMV-SV – manual , Minute volume: 2 – 30 l/Mn
			Tidal volume: approx.50 – 1400ml , Breathing frequency: approx.6-60 times/min

page 7 of 27

Equipment & Furniture Component

Flow rate range: 5 – 60 l/min

High pressure relief valve

Power supply 220VAC, 50Hz

Accessories :

Accessories required for Ventilator :

Resuscitators , Adult / Child : 1 Each

Set of face masks , 3 Sizes : 2 Each

Corrugated hoses and tubing set for Pipeline O2 : 2 Sets

Corrugated hoses and tubing set for Pipeline Air : 2 Sets

Accessories required for Anaesthesia Machine :

Hose assembly for piped Oxygen supply : 2 Sets

Hose assembly for piped Nitrous Oxide supply : 2 Sets

Hose assembly for piped Air supply : 2 Sets

Regulator and manometer for the pipe pressure hose ( 60 psig) : 1 Set

Connection from ventilator to anaesthetic apparatus , autoclavable/reusable : 1 Set

Test bag, 1 litre : 2

Peak Flow Meter : 1

Power cord with grounding wire : 1

Dust cover : 1

Bellows assembly, adult / Children : 2 Each

Patient Circuit , Magill Type , Complete , Adult / Children . . Shall be Reusable : 2

Each

Spirometer (Peak Flow Meter for Anaesthesia procedures)

Consumables for anaesthetic unit for 2 years operation:

Battery cell (as appropriate)

Soda lime for circle absorber (5Kg/pack) : 10 Packs for 1 unit

Standards

CE;

EC Marked

US FDA;

ISO certification

Syringe Driver for Parenteral Infusions , in Wards, OP, ICU’s and during Transportation/Transfer

Single Channel. Shall accept Up to 60cc Syringes , Non-Captive

Self checking of Electronics with audible call back on locked-out Controls Tamper and fluid resistant Design . ABS Casing (Impact-Resistant )

Shall be fitted with IV Rod, Adjustable Height with 4 Hooks.Mobile on 5 Star Stand with Castors

Internal rechargeable battery

Rate: 0.1 to 99.9 ml ( in 0.1 ml steps) indicatively Total volume infused: 0.1 to 999.9 ml

Precision : +/-3%.Stipulated Syringes

Occlusion release shall give minimum Bolus effect

Syringes : 10 Types at least of LuerLock Type 10/60mL.Syringes,+ Specific Choice

Pause infusion facility

Alarms/Safety

₁₃ Syringe pump Infusion nearly complete Infusion complete Occlusion

System malfunction Syringe unlocked Plunger disengaged Low battery

Protection against Leakage Current:Type CF.Equipment

Protection against Electric Shocks:Class II.Equipment

Safety features: Error coding (event log)

Rate change through Audible Stop Switch

Audible Call back on locked-Out-Controls

Automatic detection of Syringe Volume

Minimum bolus on Occlusion Release at any selected Rate Communication : RS232C Interface

Electrical:

Electrical: Class II (double insulated)

page 8 of 27

Equipment & Furniture Component

			Bat.Autonomy : 8 Hrs.Minimum
			Power supply: 220 VAC.50.60Hz
			External transformer . Stabilizer
			Environmental factors
			Shall meet IEC-60601-1-2: 2001(Or Equivalent BIS)
			General Requirements of Safety for Electromagnetic Compatibility or should
			comply with 89/366/EEC; EMCdirective.
			The unit shall be capable of being stored continuously in ambient
			temperature of 0 -50deg C and relative humidity of 15-90%
			The unit shall be capable of operating continuously in ambient temperature of
			10 -40deg C and relative humidity of 15-90%
			Accessories
			Coupler between 2 units
			Mobile floor stand
			IV stand clamp
			Rail clamp
			Standards :
			IEC601.1/IP33
			Safety: IEC 601 / 1. CF.
			Compliance with EN 60601.1 and PrEN 60601-1-24.
			CE 0459 marking in compliance with EEC 93/42 Medical Products directive.
			Comply with EN60601-1-2, EN60601-2-24
			EN ISO 9001:2000, EN ISO 13485:2000; EN 46001:1996

			HF electrosurgical unit shall be used to execute monopolar and bipolar surgery in
			many fields of application where high precision and reliability are essential
		3	Outputs of cut, coagulate and blend
			Maximum output 300 W for monopolar cut
			Activation :
			Double pedal switch which may be used for the monopolar and bipolar functions .
			Hand-switch handle
			Bipolar electrode with pedal switch or with automatic Start/Stop system ( for
			coagulation only)
			Control
			The Unit shall stop automatically in case of internal error which shall be identified on
			Display and with audible alarm
			Memorization : User shall be able to use at least 4 working programs
			Safety :
			Neutral plate safety circuit shall control connections and contacts of Neutral Plate
			with Tissues:
			Defective Contact shall be notified with visual Alarm and immediate reducing of
			power
			Output circuit : floating – protected against defibrillator interferences . Shall have HF
	Electrosurgical		leakages less than 150mA through each electrode
14	Electrosurgical		Power Supply : 220VAC, 50Hz
14	Unit (Monopolar-bipolar)		Power Supply : 220VAC, 50Hz
	Unit (Monopolar-bipolar)		Cooling: convection without fan
			Cooling: convection without fan
			Accessories :
			Single-use two button Handle , Autoclavable
			Handle shall be provided with a 3 Pins socket that shall fit majority of bipolar
			electrosurgical units
			Operative Foot-switch (usable as alternative to handle)
			Reusable neutral Plate
			Kit of 10 short autoclavable Electrodes
			Electrode wire – straight
			Electrode wire – angled 45°
			Electrode bend – 0 4 – straight
			Electrode bend – 0 8 – straight
			Electrode hook – angled 45°
			Electrode wire 1 mm.- angled 45°
			Electrode straight slip-knot – straight
			Electrode angled slip-knot – straight
			Electrode ball point – 0 3 mm. – angled 45°
			Electrode ball point – 0 3 mm. – straight
			Bipolar Forceps : 6
			Forceps shall be provided with a standard European connection
			Straight Forceps – 18 cm. (7″)

page 9 of 27

Equipment & Furniture Component

			Curved Forceps – 18 cm. (7″)
			Curved Forceps – 20 cm. (7 3/4″)
			Bayonet Forceps – 18 cm. (7″)
			Bayonet Forceps – 20 cm. (7 3/4″)
			Straight Forceps – 20 cm. (7 3/4″)
			Cable, Bipolar
			Adaptor, Bipolar Cable
			User Manual
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Suction Unit for Major Surgery Procedures . Mains-powered , mobile on 4 antistatic
			Castors, ABS Casing and 2 graduated Canisters of 2,000ml each made of
			Polycarbonate autoclavable at 121°C and disposable suction bags
			Shall require no maintenance nor lubrication
			Oil-free pump, maximum suction of at least 500 mm Hg
			Free flow rate at least 25 l/min
			Main Switch with Pilot Lamp . Fuses
			Pedal Action
			Shall be equipped with a protective thermal cut-out relay.
			Shall be equipped with motor-protection cap that totally prevents aspirated liquids or
			secretions from reaching and damaging the vacuum pump
			Suction command with continuous adjustment , Vacuometer
			2X2,000ml Canisters with airproof screwing-cap with independent Overflow devices
			. Fast Connectors and silicone Tubing
			Power Supply : 220VAC.50Hz.
			Ventilation Fan for overheating
15	Suction Pump	2	Sound level: Shall be not more than 55 dBA
			Accessories
			Silicone Tubing , sterilizable
			Transparent Cannula Holder, Sterilizable
			Anti-Bacterial Filters ( 4 )
			Set of 4 canulaes with Holder : Yankhauer , Soft Universal Yankhauer
			Diameter : 8.0/6.0mm with anti-sticking Lumen and High Suction Lumen
			Universal Soft Canulaes diameter : 6.0/4.0mm
			Frazier	Canulaes (Fergusson) diameter :1,5/2.0/3.0/4.0mm
			Jackson Canulaes : 35×3 /45X3/25X4/35X4/45X4/55X4/60X4cm
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification
			1	Operating Scissors, 170 mm, straight, blunt-blunt points	1
			2	Operating Scissors, 140 mm, straight, sharp-blunt points	1
			3	Operating Scissors, 140 mm, curved, sharp-blunt points	2
			4	Dissecting Scissors, curved, for deep surgery, 230 mm	2
			5	Operating Scissors, 140 mm, curved, blunt-blunt points	4
			6	Operating Scissors, curved, blunt-blunt points, 170 mm	2
			7	Operating Scissors, 140 mm, curved, hardened, blunt-blunt	1
			7	points	1
				points
16	Operating instrument set		8	Sharp Tips Scissors, curved, 160 mm	1
		2	9	Dressing Forceps, standard pattern ПА 150х2,5	6
			10	Dressing Forceps, standard pattern ПА 200х2,5	4
			11	Surgical Forceps, 150×2,5	8
			12	Surgical Forceps, 1 x 2, 200×2.5 mm	4
			13	Abdominal Depressor, 285 mm, blade 70 mm wide	1
			14	Tissue Forceps, 265 mm, straight	5
			15	Tissue Forceps, 256 mm, curved	5

page 10 of 27

	HSMP Armenia	Equipment & Furniture Component					HPIU: HH

			16	Hemostatic Forceps, curved, atraumatic (160 mm)				6
			17	Hemostatic Forceps, curved, 1×2 teeth, serrated,			size 2,	6
			17	(160mm)				6
				(160mm)
			18	Hemostatic Forceps, curved, serrated,		size 2 , (196 mm)		6
			19	Hemostatic Forceps, curved, serrated,		(240 mm)		6
			22	Hemostatic Forceps, straight, 1×2 teeth, serrated,			size 1 ,	3
			22	(150 mm)				3
				(150 mm)
			23	Hemostatic Forceps, curved, 1×2 teeth, serrated,			size 1,	6
			23	(150mm)				6
				(150mm)
			24	Hemostatic Forceps, curved, 1×2 teeth, serrated, size 1,				6
			24	(200mm)				6
				(200mm)
			25	Hemostatic Forceps for deep surgery, child size, size 2,				6
			25	(225mm)				6
				(225mm)
			26	Rake Retractor, 2 sharp prongs,	(200 mm)			2
			27	Rake Retractor, 3 sharp prongs,	(200 mm)			2
			28	Rake Retractor, 200 mm, 4 sharp prongs, style 2				2
			29	Rake Retractor, 2 blunt prongs, 200 mm				3
			30	Rake Retractor, 220 mm, 4 blunt prongs, style 2				4
			31	Rake Retractor, 6 sharp prongs,	(200 mm)			2
			32	Abdominal Retractor				2
			33	Needle Holder,( 200 mm)				2
			34	Needle Holder, ( 250 mm)				2
			35	Vascular Needle Holder , 160 mm				2
			36	Vascular Needle Holder, 200 mm				2
			37	Intestinal Forceps, non-crushing, curved, child size, (192mm)				2
			38	Intestinal Forceps, non-crushing, curved, adult size, (235mm)				2
			39	Tongue Spatula, straight, 20х16mm,		(180 mm)		2
			40	MОSQUITO Hemostatic Forceps, serrated, curved on edge,				6
			40	6¹/10″ (154 mm)				6
			41	Intestinal Forceps, non-crushing, straignt, adult size,				2
			41	(240mm)				2
				(240mm)
			42	Abdominal Retractor (60 mm)				2
			43	Abdominal Retractor (100 mm)				2
			44	Liver Speculum (100 mm)				2
			44	Liver Speculum (100 mm)

			Suction Unit for Emergency procedures , fitted with single 1000ml capacity
			Polycarbonate Canister , mobile on 4 Castors and carrying handle
			The Unit shall enable operation from either mains supply, or independently from an
			internal 12V rechargeable battery
			The unit shall recharge when plugged into the mains
			An	indicator on the casing shall indicate the status of the battery . A Vacuometer
			shall indicate the suction value
			Maintenance free diaphragm pump
			Overflow safety device
			The Unit shall be capable to generate 500mm Hg at least
			Free flow rate at least 25 litres per min
			Shall be fitted with easily replaceable anti-bacterial filter with 5 spare
		1	Shall provide over 30 minutes of full vacuum from a fully charged battery
17	Suction Pump		Fitted with rechargeable battery
			Operating mains voltage: 220 V – 50 Hz
			Recharging is by trickle charge and shall take eight hours maximum to restore full
			charge
			Accessories :
			Hand piece with regulator and appropriate probes shall be supplied as well as an
			additional Canister
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			The following specifications define a portable, lightweight ; battery or accumulator
18	Defibrillator		operated automated external to treat Patients requiring basic Life Support
18	Defibrillator		Weight of complete unit, excluding batteries or accumulator , shall permit easy

		2	Transport . The overall Dimensions shall enable easy storage and portability

page 11 of 27

Equipment & Furniture Component

			The Casing shall be constructed to withstand the standard operating Conditions
			in a Physician’s office and/or Hospital. The device must also with stand the
			harsh operating conditions associated with Ambulance use. The unit shall be safe to
			use both for the operator and the patient.
			Defibrillator
			The device shall utilize Biphasic waveform technology as the primary energy delivery
			option and shall include automatic and manual modes
			The biphasic waveform shall allow for escalating energies up to at least 200 Joules
			Safety: Internal discharge of energy if no discharge is effected.
			Internal self-testing and fault recognition.
			Required power 200-240V 50/60 Hz
			Weight not more 10kg
			Accessories :
			Full Standard Accessories Set-Up shall be supplied
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Intensive care ventilator, for use on Pediatric/Infant- Adult patients
			With Graphics Display Monitor.
			Breath Types: VC, PC, VTPC
			Modes ( in each breath Type): A/CMV, SIMV, SPONT,
			Spontaneous Breath Choices: PS, VTPC.
			Features:
			Inspiratory time at least 0-3 sec with optional pause
			Inspiratory flow at least 3-140 l/min
			Pressure support: at least 0 to 45cm H2O/mbar
			Tidal Volume: at least 10-800ml
			Resp.Rate: at least 6-150b/min
			Pressure Limit: 0 to 80cmH2O/mbar
			I:E Rate: 1:4 to 4:1
			Trigger pressure or flow
			FiO2: 0.21 to 1.00
			PEEP/CPAP: 0 to 45 cmH2O/mbar
		2	Leak Compensation
			Standby Condition: Allows setting to be preset and Circuit Check tests to be
			performed prior to starting Ventilation
			Open Exhalation Valve (BPRV): On/Off for Biphasic Pressure Release
			Ventilation
			Event History Log: Records 1000 events; alarm & settings
19	Ventilator ICU		Compliance Compensation: On/Off
19	Ventilator ICU		Graphical display of respiratory parameters
			Graphical display of respiratory parameters
			Must be mounted over the Mobile Medical Air Compressor.
			Power requirements
			220 VAC ±10%, 50Hz.
			Internal rechargeable Battery provides an minimum. 60 minutes for complete
			ventilator function.
			Accessories :
			Medical Air Compressor
			Humidifier
			1 Tube set, adults
			1 Tube set, Children
			1 Humidifier chamber
			O2-connecting Tube 5.0 m
			1 Air-connecting Tube 5.0 m
			Humidifier : Heating power with safety thermostat and indication of operating status
			1 Circuit , Adults with patient Tubes , water traps, Y-Piece,mask elbow, catheter
			connector
			1 Circuit , Children with patient Tubes, water traps, Y-Piece,mask elbow, catheter
			connector
			1 Carriage
			Articulated Bracket for rail
			O2-cell without housing

page 12 of 27

Equipment & Furniture Component

			Sensors 5 pcs set
			Temperature Sensor
			Humidifier
			Bag- test-lung
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Real-time SpO2%
			Oxygen Saturation Range (%SpO2)
			Measurement range at least 70-99%
			Accuracy (%SpO2) ±2% at100%~80%, ±3% at 80%~70%
			Real-time heart rate (BPM)
			Pulse
			Measurement range 30-250 bpm
			Accuracy ± 1 bpm at 30~250 bpm
			Display
			SpO2,Pulse rate, Pulse signal wave, Max/Min setup (SpO2% / BPM)
			Power Requirements internal rechargeable battery providing an operating time of at
			least 8 hours
			Compact design for easy transportability
20	Pulsoximeter
		2	Accessories:
			3 rolls of paper
			Operation manual
			1 adult reusable finger Sensor
			1 Neonate Sensor
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Patient monitor that shall draw Cardiograms, measures Blood Pressure (invasive or
		7	not-invasive type), Respiration values, Temperatures at two spots, Oxygen Saturation
			in arterial blood ( SpO2 ), and Pulse rate ( HR ) .
			May be used to Monitor Patients on the transportation by using batteries, and the
			measured information on patient’s condition shall be displayed in wave forms along
			with numerical values.
			Display/Screen
			Display : Colour TFT display , screen diagonal Curves and measured values : not less
			than 25.00cm . Up to 6 Curves as well as numerical fields
			Brightness: can be manually adjusted
			Sweep Speed : Shall adjuste to 6.25, 12.5, 25 and 50 mm/s
			Display pixels: at least 1024×768
			Monitor Interfaces
			R-SYNC: for defibrillator , Each R-wave shall be clearly identified , Staff call:
21	Patient Monitor, ICU		Remote alarm via alarm adapter
21	Patient Monitor, ICU		RS-232: as computer interface
			RS-232: as computer interface
			Mains/Battery Operation
			Mains operation: shall be via built-in Power Supply Battery operation: via integrated
			battery or Charging console . Battery operating time: approx. up to 4 hrs at least
			Power Supply : 220 V AC ±10%, automatic change-over Power failure buffer : for
			trend values,
			System Expansion
			Software updates via interfaces
			Monitoring parameters shall include : ECG, RESP, IBP, NIBP, SPO2, PULSE RATE
			, DUAL-TEMP
			S-T segment synchronized detection and analysis
			Graphic and tabular trends of all parameters for at least 96 hours
			20-Mn minimum ECG real time waveform and parameters storage and review
			Shall be able to be connected with a Central Monitor Station

page 13 of 27

	HSMP Armenia	Equipment & Furniture Component		HPIU: HH

			Inner high-definition thermal dot matrix recorder optional, which can output
			waveforms and characters
			ECG : Input : Whole-lead ECG cable, standard AAMI cable connector
			Sweep speed: 12.5, 25, 50mm/s 0.5~40Hz(for monitor or operation)
			Calibration signal: 1mV , Protection: Against electrosurgical interference and
			defibrillation
			Heart Rate: Measuring range: 30~250bpm , Alarm mode: Audible and
			visualAlarm
			Respiraton Measurement Range: at least 0~60 bpm
			Oxygen Saturation(SPO2) Meas. Range: at least 70~100%
			NIBP : Method: Oscillometric , Mode: Manual, Auto , Resolution: 1 mmHg
			Shall have Over-pressure protection: (Adult 300mmHg ; Child 220mmHg
			Temperature : Meas. Range: at least 20~50C , Resolution: 0.1 C , Accuracy: +/- 0.2 C
			Operation Environment : Temperature: 0~45C , Humidity: 30~85%(non-condensing)
			Accessories
			Electrode cable for disposable electrode (3 leads)
			NIBP cuff for adults
			NIBP cuff for children
			Hose for NIBP cuff
			Respiration Sensor
			Power cord
			Disposable electrode (5 pcs)
			Temperature sensor – Adult (rectal)
			SpO2 sensor reusable
			Console / Bedside Holding Device
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Patient monitor that shall draw Cardiograms, measures Blood Pressure (invasive or
			not-invasive type), Respiration values, Temperatures at two spots, Oxygen Saturation
			in arterial blood ( SpO2 ), and Pulse rate ( HR ) , End Tidal CO2 (etCO2) .
		2	May be used to Monitor Patients on the transportation by using batteries, and the
		2	measured information on patient’s condition shall be displayed in wave forms along

			with numerical values.
			Display/Screen
			Display : Colour TFT display , screen diagonal Curves and measured values : not less
			than 25.00cm . Up to 6 Curves as well as numerical fields
			Brightness: can be manually adjusted
			Sweep Speed : Shall adjuste to 6.25, 12.5, 25 and 50 mm/s
			Display pixels: at least 1024×768
			Monitor Interfaces
			R-SYNC: for defibrillator , Each R-wave shall be clearly identified , Staff call:
22	Patient Monitor, anesthesia		Remote alarm via alarm adapter
22	Patient Monitor, anesthesia		RS-232: as computer interface
			RS-232: as computer interface
			Mains/Battery Operation
			Mains operation: shall be via built-in Power Supply Battery operation: via integrated
			battery
			or Charging console . Battery operating time: approx. up to 4 hrs at least
			Power Supply : 230 V AC ±10%, automatic change-over Power failure buffer : for
			trend values,
			System Expansion
			Software updates via interfaces
			Monitoring parameters shall include : ECG, RESP, NIBP, SPO2, PULSE RATE ,
			DUAL-TEMP and etCO2
			S-T segment synchronized detection and analysis
			Graphic and tabular trends of all parameters for at least 96 hours
			20-Mn minimum ECG real time waveform and parameters storage and review

page 14 of 27

		Equipment & Furniture Component

			Shall be able to be connected with a Central Monitor Station
			Inner high-definition thermal dot matrix recorder optional, which can output
			waveforms and characters
			ECG : Input : Whole-lead ECG cable, standard AAMI cable connector
			Sweep speed: 12.5, 25, 50mm/s 0.5~40Hz(for monitor or operation)
			Calibration signal: 1mV , Protection: Against electrosurgical interference and
			defibrillation
			Heart Rate: Measuring range: 30~250bpm , Alarm mode: Audible and visual Alarm
			Measurement Range: at least 0~60 bpm
			Oxygen Saturation(SPO2) Meas. Range: at least 70~100%
			NIBP : Method: Oscillometric , Mode: Manual, Auto , Resolution: 1 mmHg
			Shall have Over-pressure protection: (Adult 300mmHg ; Child 220mmHg
			Temperature : Meas. Range: at least 20~50C , Resolution: 0.1 C , Accuracy: +/- 0.2 C
			End Tidal CO2 (etCO2) Module , Non Dispersive Infrared Spectroscopy Method
			Mainstream or sidestream
			Displayed Data : Waveform labels and annotations ,	etCO2, inC02 and respiration
			rate values
			etCO2 Alarm Limits
			Operation Environment : Temperature: 0~45C , Humidity: 30~85%(non-condensing)
			Accessories
			Electrode cable for disposable electrode (3 leads)
			NIBP cuff for adults
			NIBP cuff for children
			Hose for NIBP cuff
			Respiration Sensor
			Power cord
			Disposable electrode (5 pcs)
			Temperature sensor – Adult (rectal)
			SpO2 sensor reusable
			EtCO2 Mainstream or Sidestream accessories , Transducer , Lines , Filters
			Console / Bedside Holding Device
			Standards
			Classification: CF, defibrillation-proof,
			CE;
			EC Marked
			US FDA;
			ISO certification
			Compact and easy to transport oxygen concentrator ( Mobile on Castors )
			The Oxygen Concentrator shall feature a dual-head Compressor. One head
			producing. Capacity : 1 to 5 l/Mn of O2 at 90% minimum at maximum flow
			Pressure-compensated Flowmeter shall permit use of long canula while maintaining
			accurate flow setting.
			Safety Alarms: Audible and visual : Power Failure , Restricted Flow , , Low O₂
			Pressure-relief Valve and thermal protection of the Compressor
			Double-insulated Unit , Two-prong plug
			Flame-retardant Cabinet
			Sound Level (ANSI): 50 dB average
23	Oxygen Concentrator		Fixed humidifer Port and Recess shall prevent bottle and connector breakage
23	Oxygen Concentrator
		1	Power Requirements: 220 VAC,50 Hz
		1
			Accessories :
			O2 Tubing , 3 Face Masks ( Adult , Infant , New Born ), Humidifier ,
			Set of Filters
			Standards
			CE;
			EC Marked
			US FDA;

page 15 of 27

		Equipment & Furniture Component

			ISO certification
			Manufactured from chrome plated steel tube, three sections with independent
			manual controls and Trendelenburg position.
24	Couch, Gynecology	4	Top is upholstered with washable plastic material and flame retardant.
			Complete with padded Goepel leg-holders and S.S. bowl.
			Knock down construction.
			Manufactured from reinforced epoxy-painted steel tube
			Three sections with independent manual controls.
			Trendelenburg position.
25	Delivery Bed		Third section extensible.
		2	Top is upholstered with washable plastic material flame retardant.
			Complete with S.S. tray, and two adjustable knee crutches, padded shoulder rest,
			handgrips, leg-holders.
			Lamp , Examination . Mobile on 5 Castors , 5 star-shaped	Heavy and stable Stand .
			Halogen Type
			Height of LampHead shall be adjustable
			Light Intensity shall be at least 15000 Lux with a Field radius of 17cm Minimum
			Color Intensity : 4300 °K. Single Reflector of 150mm Minimum
			Power rating : 1X40W Minimum . 220VAC/50Hz . Transformer , 24V DC shall be
26	Examination Lamp	3	included
26	Examination Lamp		Accessories /Spares : 5 Halogen Bulbs
			Accessories /Spares : 5 Halogen Bulbs
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification
27	Uterine Aspiration Set	1	Stainless steel with handle for suction regulation.
27	Uterine Aspiration Set		Cannule ø mm. 6/8/10/12/14
			Cannule ø mm. 6/8/10/12/14

			CTG or Fetal monitor for recording and analyzing the fetal heart rate (FHR) on beat-
			to-beat basis and the uterine contraction with Doppler -US transducer and taco
			transducer.
			Portable handheld CTG monitor. Compact and battery operated, shall allow Patients
			to be continuously monitored anywhere . Color display shall show the CTG data
		1	presented in standard format for easy interpretation.
			Fetal signals shall be easily located using the wide angle transducers with
			contractions stress being monitored by an external pressure transducer. Audio signals
			of each fetal heart are available on selection by the user through the built in Audio
			system.
			The user will have control over the audio volume, audio fetal channel, chart recorder
			speed, toco zero, and event mark via the units front panel push buttons.
			Directional and watertight Ultrasound and TocoGraph with color-coded transducers
			for Single and Twins
			Transducer: Multi element wide angle
			Range: 30 to 240 bpm
			Power output: < 20mW/cm2
			Toco
28	Fetal Monitor		Transducer: Real Time uterine Activity (contractions) trace on standard scale format
28	Fetal Monitor		Digital autocorrelation shall provide accurate and reliable FHR traces

			A pre-cut, non-fray elasticised belt with Buckle shall enable easy Transducer
			positioning for more accurate traces in difficult monitoring situations
			Clinical Event marker & automated foetal movement detection . Trace annotation
			Comprehensive patient database
			Shall store over 500 patient records (30 minutes traces) in internal memory of FHR,
			Toco , Fœtal Movements with unlimited data storage on plug-in PCMCIA memory
			Cards
			Computer interface 3 wire RS232
			Thermal printer for common CTG paper
			Speeds: 1,2,3, cm/min
			Paper: z-fold pre-printed chart scale
			The grid and the FHR/UA trace shall be printed simultaneously , ensuring printing
			accuracy and preventing potential errors in interpretation due to paper drifting or pen

page 16 of 27

		Equipment & Furniture Component

			jitter
			Power Supply :220 V AC and DC battery operated
			Accessories:
			1. Belts : 1 Original + 1 Spare Set
			2. Buckles
			3. IUP Starter Kit
			4. Multicrystal transducer
			5. Toco Transducers
			6. Event marker Consumables:
			7. CTG printer paper : 20 Packs
			8. Fetal scalp electrodes
			9. Ultrasound gel
			10. IUP catheters
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification
			Capacity-0-15 kg
29	Scale for newborn children	3	Graduation-10 gr.
		3	Precision-+/- 10 gr.


			Washable surface

			Body with 6V 20W Halogen for 220V, 50 Hz.
			Quadruple revolving nosepiece.
			Sturdy,base with supportive rubber feet.
			With low position, coaxial coarse and calibrated fine focus control, with graduation
			reading 2 microns per division.
			Total focusing 40 mm.
			Condenser adjustable.
30	Microscope Binocular	1	Built-in Power supply , halogen bulb adjustable.
30	Microscope Binocular	1	Double layer mechanical specimen stage.
			Double layer mechanical specimen stage.
			Dust cover, blue filter, immersion oil and instruction manual included.
			2 pcs. 6V 20W halogen bulbs included.
			Binocular Head, 30° inclined, 360° rotatable, Interpupillary Distance 55 – 75 mm
			Objectives:
			ACHRO 4x/0.10
			ACHRO 10x/0.2
			ACHRO 40x/0.65, spring loaded
			ACHRO 100x/1.25, Oil, spring loaded

			Microscope with metal base with 360° rotatable monocular tube, 45° inclined
			3-fold objective nosepiece
			separated coarse and fine focus
			Stage focus control (protection of sample!)
			Objectives:
			ACHRO 4x/0.10
			ACHRO 10x/0.25
			ACHRO 40x/0.65 spring
31	Microscope Monocular	1	Objective 100x/1.25 oil,
			attachable mechanical stage, etc.
			Abbé condenser n.A. 1.25 with iris diaphragm, variable at height
			Stage with stage clips
			Blue filter.
			Built-in illumination 6V/20 Watt Halogen, adjustable
			Daylight mirror for outdoor-use
			Dust cover.
			Packed in styrofoam case
			Power Requirements: 220V / 50 Hz.

page 17 of 27

Equipment & Furniture Component

To provide accurate and precise hematology results with WBC 3 parts differential. Principle method of detection: volumetric impedance, electrical impedance, laser flow cytometry, hydrodynamic focusing or equivalent.

It should be able to provide precise measurement of

White Blood Cells count (WBC): Precision (CV, coefficient of variation) < 3.5%
Red Blood Cells (RBC) : Precision (CV) < 2%
Platelets (PLT) : Precision (CV) <6.0%, linearity range: 10 – 950×10⁹/L
Hemoglobin (Hgb)
Hematocrit (HCT)
Mean corpuscular volume (MCV)

Mean corpuscular hemoglobin (MCH)
Mean corpuscular hemoglobin concentration (MCHC)

Red blood cell distribution width coefficient of variation (RDW-CD) 1 10) Mean platelet volume (MPV)

Lymphocyte (L% & L#)
Monocyte (M% & M#)
Granulocyte (G% & G#)
Others

Please indicate all parameters included in the offer here Minimum WBC 3 parts differential

Minimum 3 histograms

³² Shall have dual sampling mode of both whole blood as well as capillary vascular ^{Analyzer Hematology} Efficient work flow control with patient selective testing

Shall be an open system to accept generic reagents and/ or local made reagents All reagents shall be cyanide free

With build-in printer

With quality control function and reporting

With programmable automatic cleaning and maintenance

Accept samples with any anticoagulant including EDTA, heparin and citrate acid Data storage of approximately 300 samples.

Approximately 60 samples/hour With operation menu, reporting

Possible with interfacing capabilities to external PC, Built-in Printer, LIS software or Network

The system offered shall be designed to operate normally under the conditions of the purchaser’s country. The conditions include Power Supply, Climate, Temperature, Humidity, etc.

Please declare in detail compliance of this item offered with any relevant quality and safety standards.

RS232

Power Supply : 220VAC.50Hz. Accessories :

Start-up Reagents as per Manufacturer

		Compact semi-automated urinalysis instrument with a throughput of 50 tests/h
		Shall have individual setting of concentration ranges, grades and units
		Automatic urine colour determination
		Memory capacity of 150 results at least
		Interface ports for connection to PC , bar-code reader and external printer
		Results based upon test strips
		Shall have long period calibration stability
		Automatic compensation of intrinsic urine colour avoiding false positive results
	1	Power Supply :
33	Urinalysis System	220VAC.50Hz .
33	Urinalysis System	Accessories:
		Accessories:
		Strips , 1000 pcs
		Calibration Testing Trips
		Standards
		CE;
		EC Marked
		US FDA;
		ISO certification

34	Chemistry Analyzer	At least 100 tests/hr
34	Semi- Automatic	Including end point and kinetic measurement
	Semi- Automatic	Including end point and kinetic measurement
		Capable of analysing serum, plasma, urine and CSF

page 18 of 27

Equipment & Furniture Component

Automatic calibration

Indication of abnormal values

Computer interface

Analysis of Albumin, ALP, ALT, AST, BUN, Ca++, Cholesterol, CK, Cl-, CO2,

Creatinine, Direct and total bilirubin, Glucose, Inorganic phosphorus, Iron, K+,

LDH, Mg, Na+, Total protein, Triglycerides, Urea, Uric acid and others

		1
			Coagulometer	with 2 independent operating channels , Semi automatic operation
			Tests performed: PT, APTT, Fibrinogen, cofactors II, V, VII, VIII, IX, X
		1	Optical detection with magnetic stirring used to detect clots
			Temperature regulated at 37ºC ± 0.1ºC
			Automated test calculation following addition of reagent, automatic compensation
			for blanks
			Straight forward input of test parameters, incubation period, tolerance for test
			performed in double, reagent data (ISI, unit)
			Automatic calibration/self test system
			Capability to store calibration curves, presenting results in different units (second,
			%, ratio, g/l or mg/ml.
			Capacity PT: 60 in duplicate/per hour, APTT 45 in duplicate/per hour
			LCD/LED display
			Incubator capacity: 10 tubes
			RS 232 interface for transferring results to PC or printer
			Power supply:	240VAC, 50Hz .
			Accessories :
			Thermoprinter
35	Coagulometer		Starter kit consisting of 100 pcs of cuvettes with magnetic stirs
			Consumables:
			PT tests
			APTT tests
			Fibrinogen tests
			Printer paper 20 meter rolls
			Reagent cuvettes, 100 pcs
			Magnetic stirrers, 10 pcs
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Precise Temperature Control up to 99 ºC
			Model with Capacities : 6 L
			Seamless Stainless Steel Bath
36	Water Bath	1	Range Ambient +5ºC to 99ºC
			Temperature Accuracy ± 0.5ºC
			Uniformity ± 3.0ºC
			Power Requirements: 220VAC / 50 Hz.

			Productions rate: not less than 4 L/Hr
			Standard equipment includes low water cut-off protecting heating elements from
37	Water Still	2	burnout when water supply is interrupted
37	Water Still		Drainage Tap
			Drainage Tap
			Power Requirements: 220V / 50 Hz.

			Centrifuges are required in the Laboratory to separate various components of Blood
			for analysis.
			Operational Requirements :
38	Centrifuge		Table top version
			Technical Specifications:
			Tube Capacity :No. 24 – 36 : Size 5 – 15 ml
			Should have a digital timer

page 19 of 27

		Equipment & Furniture Component

			Body should be made of strong fabricated & corrosion resistant steel
			Control panel – for start/stop switch, dynamic brakes, step less speed regulator with
		1	zero start switch & speed indicator with timer and protective fuses.
			Door interlock
			Maintenance-free brushless drive motor with exact speed pre-selection and display.
			Speed range 100 to 5000 rpm and above, accuracy 1 rpm.
			System Configuration Accessories, spares and consumables
			Centrifuge complete with Swing and basic rotors	, 8 seats , and buckets
			Tube Holders as appropriate , 15 ml Tubes
			Environmental factors :
			Shall meet IEC-60601-1-2: 2001(Or Equivalent BIS) General Requirements of
			Safety for Electromagnetic Compatibility.
			The unit shall be capable of being stored continuously in ambient temperature of 0-
			50 deg C and relative humidity of 15-90%
			The unit shall be capable of operating continuously in ambient temperature of 10-40
			deg C and relative humidity of 80%
			Power Supply :
			Power input to be 220-240VAC, 50Hz .
			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification

			Incubator 37° C – Outer case, inner case and front door manufactured with 18/10
			stainless steel, insulated with high grade glass wool.
			Door with silicon gasket and lock key. Front see-through inspection window.
			Heating elements shielded with 18/10 stainless steel.
			Adjustable mesh shelves manufactured with 18/10 stainless steel. Forced air
39	Incubator laboratory	2	ventilation.
39	Incubator laboratory	2	Thermostat
			Thermostat
			Thermometer with analogical dial. Safety thermostat.
			Possibility of continuous running : 0-120 min.
			Capacity not less than 60 liters
			Power Requirements – 220 ± 10% V. 50 Hz.

			For medicine storage.
			Upright Type
			Internal volume not less than 250 lt. / freezer – 40÷50 lt.
40	Refrigerator	3	Temperature controlled within the range of +2°÷ +8° C.
		3	Number of shelves – 3 or 4.
			Number of shelves – 3 or 4.
			With defrosting system
			Power Requirements: 220 ± 10% V. 50 Hz.
			Horizontal autoclave, benchtop Type for CSSD,	Laboratory , OutPatient/Wards
			Sections
			Self-contained ,front-loading and fully automatic Unit with integrated Steam
			Generator .
			The Unit shall be single Manual Door Type
			Stainless Steel Chamber and Door : Z3CN18/10
			Capacity per cycle shall be at least 100L for a Cycle time of not more than 25 Mn.(
			Sterilization Phase at 134°C).
			Sterilization shall be enhanced by the use of Vacuum Cycle Digital temperature
			control and timing , Pressure Control , fully programmable cycle parameters
41	Autoclave		Low Water alarm, Door Safety Locks, Program Cut-Out in case of Power Failure ,
			Automatic Zeroing. Cycle End Alarm
		2	During Cycle progress , Door is locked into position by both Temperature and
			Pressure Interlocks . Rapid single action door closure shall be of concern
			Electronically-operated Vent valve , Automatic Air Purging , Over Pressure Safety
			Valve and Low Water Cut-Out with Visual and Audible Alarm indication shall be as
			standard
			The Unit shall be equiped with at least 4 Stainless Steel Trays
			Power Supply: 220VAC.50Hz .
			Accessories :
			4 Stainless Steel Trays

page 20 of 27

		Equipment & Furniture Component

			Standards
			CE;
			EC Marked
			US FDA;
			ISO certification
			Electronic Controlled Sterilizing Process
			Outer case and internal chamber – constructed from stainless steel.
			Two or three adjustable shelves.
			Wall and hinged Door Insulated with High Grade Glass Wool.
42	Hot air sterilizer	3	Door with Lock and Flat Key.
42	Hot air sterilizer		Temperature: adjustable from +50ºC to +200 ºC ±10 %.
			Temperature: adjustable from +50ºC to +200 ºC ±10 %.
			Timer Range: 0-250 minutes. ±10 %.
			Capacity: 50- 60l.
			Power requirements
			220 VAC ±10 %, 50Hz.
	Scale for Adults	1	Capacity-5-150kg.
43	Scale for Adults	1	Graduation-100gr.
43			Graduation-100gr.
			Precision-25 gr.
			Washable surface.
			Manual Resuscitator, Autoclavable,with unidirectional Valve
			The supply of Filters shall permit the use in Toxic Atmosphere
			Adapted to First Emergencies the unit shall also the complement to all automatic
			Ventilation
			Designed for Adults . Shall be supplied with 2 Masks
			All parts shall be autoclavable up to 134° C.
			The device shall consist of a self-filling Bag of thin Silicone Rubber which shall
			transmit adequately the User’s Fingertips Action with a high degree of ‘feel’
			indicative of Pressure and Volumes Changes
			An inflating valve ( Transparent Polysulfone ) shall be fitted between the orifice of
			the Bag’s Delivery End and 2 Rubber Face Masks shall be supplied
			Designed Leak shall counteract Inflating Pressure for all Lung’s Conditions
			A pressure relief valve shall be incorporated to comply with BS 6850.1987
			Balloon : Silicon 1,5L
		1	Safety Pressure : 30 cm H2O
44	AMBU emergency case	1	Accessories :
44	AMBU emergency case		Accessories :
			Balloon , autoclavable
			Valve, autoclavable
			Valve Obturator
			PEP Valve Adaptor
			2 Masks vinyl, Adult / Children with Straps
			Tube for Pressure retake
			Plastic carrying case
			Standards:
			CE;
			EC Marked
			US FDA;
			ISO certification
			Bacterial Lamp for Air Sterilization by means of UV Beams , UVC Category or Far
			UV (200nm< >280nm) with Strong bactericide effectiveness with a maximum
			strength situated at 265nm (253.7nm Mercury Spectra )
			UVC shall be emitted thru vacuum ionizing Tube ( Weak permeation )
			Useful power shall be at least 45% of nominal power (30W)
			LifeTime shall be at least 7500 Hrs
45	Bacteriological light	15	Radiation shall be witnessed by means of blue Light emission
45	Bacteriological light	15	Encased in Steel Sheet casing , Epoxy-painted. Ceiling or wall fixation
			Power supply:220V.AC50 Hz.
			Accessories/Spare Parts:
			Ionized Tube : 5

46	Infusion fluid holder

page 21 of 27

		Equipment & Furniture Component

		20	IV Pole , Mobile on Castors
			Adjustable height
			2 Hooks

			Manufactured from chrome plated steel tube
			Upholstered fixed Top covered with washable plastic material , Flame Retardant
			Complete with side Rails and IV Stand
47	Patient trolley	5	Mounted on 4 casters 100 mm two of which with brakes
		5	Knock down construction.
			Knock down construction.
			Length min. –2000 mm.
			Height – 700 mm.
			Nursing incubator mobile on castors
			Temperature control by air temperature or skin temperature
			Temperature control range 20-37 °C
			Display of temperature
			Alarms
			High and low air temperature
			High and low skin temperature
48	Incubator neonate		Fan failure
48	Incubator neonate		Sensor failure
			Power failure
			Secondary thermostat
			Heater power indicator
			At least 2 hand ports
			At least 2 tubing ports
			Provision for oxygen supplementation
			Provision for humidity supplementation
			Internal noise < 60 dB(A)
			Power supply 220 V 50 Hz
			Mobile, Stand-type.Max. Light intensity (Ec) up to not less than 110
			000 lx or more Color rendering index (general) Ra 94-96 Color
			rendering index (red) R9> 90	Light field size approx. 13-25 cm. Co lour
49.	Surgical light mobile		temperature 4200º K (approx.) Working range without focusing
49.	Surgical light mobile		intensity approx.70 – 130 cm	Power supply 220 V, 50 Hz Light source 3
			intensity approx.70 – 130 cm	Power supply 220 V, 50 Hz Light source 3
			x halogen approx. 23 V /50 W	Durability of halogen bulbs 1300 h or
			more Adjustment of light intensity approx.50 – 100% (0-100%)
			Sterilizable handle
50.	Splint set		Available
51.	Transportation splint		Available
52.	Stretcher		Available
54.	Tracheostomy set		Available
			Optical System
			Field of view: 100°÷ 120°
			Depth of field: 3÷50 mm.
			Distal end
			Bending Section
			Range of tip bending: not less than Up 180°, Down 130°.
			Insertion tube
			Outer diameter: not more than 5.0mm
			Working length: not less than 600mm.
			Total lenhgth: not more than 900mm.
55.	Fiber bronchoscope		Instrument channel
55.	Fiber bronchoscope		Inner diameter: not less than 2.0mm.
			Inner diameter: not less than 2.0mm.
			Light Source
			Mobile
			Lamp
			Type:Quartz halogen.
			Output: 150W.
			Cooling fan prolongs lamp life not less than 500 hours.
			Air/Water functions available
			Power consumption:not more than 250 W.
			Power Requirements – 220 ± 10% V. 50 Hz. standard network
			Weight: not more than 6 kg.

page 22 of 27

		Equipment & Furniture Component

			Telescope: 1.2mm , 0º direction of view. Trocar Tube: 1.2mm Trocar
			spike: 1.2mm Accessories: Adapter with Luer lock male and x-mas tree
			Telescope holder Light quid, 3.5m with condenser Trocar Tube for
56.	Arthroscope		surgical instruments 2mm Trocar spike 2mm pointed Trocar spike 2mm
56.	Arthroscope		blunt Palpation Probe 2 mm straight -4pcs. Palpation Probe 2mm Hook

			Type -4pcs. Knife 2mm side cutting -4pcs. Knife 2mm front cutting –
			4pcs. Rasp 2mm -4pcs. Biopsy Forceps 2mm -4pcs. Grasping Forceps
			2mm -4pcs. Instruments Tray Shaver System
			Optical System Field of View: 80º minimum Direction of View: Lateral,
			Rear-view 15º minimum Depth of Field: 5-60 mm minimum Distal End
			Outer Diameter: max. 12.0mm Instrument Channel Inner Diameter:
57.	Duodenoscope		minimum 2.8mm Insertion Tube Outer Diameter: max. 11.0mm
			Working Length: minimum 1235mm Bending Section Range of Tip
			Bending minimum: UP 120º, Down 90º Right 110º, Left 90º Biopsy
			Forceps Minimum Visible Distance: 10 mm from Distal End
			Laparoscopy Surgery Set Including:
			Forward-Oblique Telescope 300 deg, diameter 10mm, length 31cm,
			including
			fiber optic light transmission incorporated. Color code: red.
			Forward-Oblique Telescope 300 deg, diameter 5mm, length 29 cm,
			including
			fiber optic light transmission incorporated. Color code: red.
			VERESS Pneumoperitoneum Needle with spring loaded stylet LUER-lock,
			length 13 cm.
			Trocar 11mm with Cannula and multifunctional valve.
			Trocar 6mm with Cannula and multifunctional valve.
			Reducer 11/5mm.
			Reduction Sleeve, reusable, instrument diameter 3mm, trocar cannula O.D.
			6 mm.
			Reduction Sleeve, reusable, instrument diameter 10mm, trocar cannula O.D.
			15 mm.
			Reduction Sleeve, reusable, instrument diameter 5mm,trocar cannula O.D.
			11 mm.color code:green
			Dissecting and Grasping Forceps, rotating, with connector for unipolar
			coagulation size 5mm, length 36 cm.
			KELLY and Grasping Forceps, rotating, with connector for unipolar
			coagulation size 5mm, length 36 cm.
	Laparoscopy system with		KELLY Forceps insert, long
58.	instrumentation for		MANHES grasping forceps with connector for unipolar
	general surgery		coagulation 5mm, length 36cm
			METZENBAUM scissors, rotating, with connector for unipolar
			coagulation 5mm, length 36cm,blades curved, double action jaws, length of
			blades 12 mm.
			Insert METZENBAUM scissors
			Hook Scissors, rotating, size 5mm, length 36cm,single action jaws
			Coagulating and Dissecting Electrode, L-shaped, with connector pin for
			unipolar coagulation size 5mm, length 36 cm
			Coagulating and Dissecting Electrode, spatula-sheaped, blunt with
			connector pin for unipolar coagulation size 5mm working length
			Insert Micro-dissecting scissors
			BLAKSSLEY Forceps insert
			Suction and coagulation cannula, L-shaper
			Take-apart Bipolar Coagulating Forceps
			Insert Forceps
			Applier for ligating clips (medium large) dismanting, rotating
			Pilling-Titanium-Clips, medium-large, sterile box with 16 cartridges,
			10clipseach
			Electronic CO2 Endoflator, CO2 bottle empty, power supply, 240 VAC, 50
			Hz,
			CO2/ N2O gas filter for use with	Electronic Endoflator
			High Frequency Surgery Unit, power supply: 200-240 VAC, including: 400
			A Mains Cord Adaptor, unipolar HF- output, 4 mm/5 mm

page 23 of 27

		Equipment & Furniture Component

			Connecting Cord, for connecting the neutral electrodes
			Neutral-Electrode made of conductive silicone, with 1 rubber strap for
			fastening contact face, surface area approx. 180 sq.cm.
			Two-Pedal Footswitch, for control of coagulation.
			Monopolar High Frequency Cord with 5 mm plug for HF-unit, length 300
			cm
			Suction Bottle, 1.5L.
			Bacterial filter
			Cold Light Fountain: approx. 175 W power supply: 220-240 VAC, 50 Hz
			Fiber Optic Light Cable, size: 4.8 mm, length 180 cm
			Endoscopic video system, color system PAL power supply: 240 VAC, 50
			Hz.
			Cover for use with endoscopic video cameras, size 17 x 242 cm, rolled up.
			Sterile, in packs of 15.
			Color Monitor, color system PAL, NTSC screen 45 cm power supply: 240
			VAC, 50 Hz including: mains cord
			Mobile cart for video system: 4 antistatic dual wheels, 2
			equipped with locking brakes, 2 fixes shelves, 1 drawer unit with lock, 1 set
			of non-sliding stands for units, inclusive integrated small cable conduit in
			both vertical boom, 1 camera mount. Power Box socket board with 12
			plugs, 12 grounding plugs Approximate Dimensions: cart: 700mm x
			1280mm x 686mm (wxhxd) Shelf 630mm x 480mm (wxd) caster diameter:
			125 mm

			Electroencephalograph- analyzer. Based on the personal computer. Routine
			EEG studies with computerized analysis and topographical mapping, in-
			depth analysis of EEG/EP activity, analysis of	epileptiform activity, long-
			term EEG monitoring , differential diagnosis	24-EEG inputs. Sensitivity:
			0.1 µV to 200 µV. Calibration µV: square (1Hz.) or Sine (5Hz) signal of 5,
59.	EEG		10 ,20, 50, 100, 200 and more High frequency filter: >70 Hz at highest
59.	EEG		setting) Low frequency filter: <0,3 Hz at lowest setting) AC Rejection

			filters (50/60 Hz.): 1:1000 or better. Automatic suppression of miographical
			artifacts: 20 dB (30 Hz.) or better. Digital signal processing: 22-bit ADC
			Software-controlled Photo and Audio stimulators. Check-up of electrode
			impendence. Power Requirements – 220 ± 10% V. 50 Hz. standard network
			Standard set . Set of standard accessories. EEG-gel 2 kg.
			Gantry
			Number of slices per rotation-2
			Gantry aperture: at least 65 cm
			Gantry inclination angle: at least. 20 degrees
			Complete scanning time: 1.5, 2.0, 3.0, 5.0 sec app.
			Min. scanning time: app. 1.5 sec
			Patient table
			Coverage region: 70 cm
			Table height: 40-90 cm
			Scanning horizontal range: 120 cm
			Max patient weight: app. 180 kg
			Acuracy of horizontal movement +/-: 0,25 mm
			Detector
60.	CT-scanner		Detector type: Solid body
			Number of detecting elements: at least 708 per row
			High-contrast resolution: at least 13 par. line/cm at 0% MTF
			Low-contrast resolution: less than 4 mm at 0,3% at 20 mGy
			X-ray subsystem
			X-ray generator capacity: min 24kWt
			mA range at least 20-250 mA
			kVp range at least 80-140 kV
			Scanning parameters
			Max duration of spiral scanning: 60 sec
			Pitch: 0,1:1 to 3,0:1
			Slice thickness: 1,2,3,5,7,10 mm
			Min slice thickness: 1mm
			Summary volume of hard discs: min 80GB
			Monitor: LCD

page 24 of 27

		Equipment & Furniture Component

			Monitor size: min 17’’
			Power requirements: 380V, 3-phase.

			General Description: General purpose portable ultrasound scanner, with
			multiple focus electronic probes. 1. System Specifications: PROBES:
			Electronic 3.5MHz convex Electronic 7.5 MHz linear Scan Modes: B, M,
			B+M, B+B Scan Converter: −Matrix size: min 512x512x8 −Gray-scale
			levels: min 256 Software Features: −Multiple beam focusing −Image
	Portable ultrasound		preprocessing −Image postprocessing −Zoom −Digital calipers −General
61.	Portable ultrasound		analysis: distance, area, circumference −Obstetrics software
61.	scanner
	scanner		packageKeyboard: Alphanumeric keyboard with	pointing device (joystick
			packageKeyboard: Alphanumeric keyboard with	pointing device (joystick
			or trackball). Maximum Display Depth, cm: 22 or more Monitor: High
			resolution monochromatic, minimum size: 7-inch Connections: -standard
			video output 625 lines / 50 Hz -image freezing footswitch Power
			Requirements: -Mains: 220V, 50Hz -Rechargeable battery, minimum
			capacity: 1 hour WEIGHT: maximum 15 kg
			Type : Galilean Magnification : 4.5X, 7.5X, 11.5X, 18.5X, 29.5X or similar
			Field of View : Ø 49 mm to Ø 8 mm Illumination : Achromatic shadow
62.	Surgical microscope for		free spot Light Source : Cold light through fiber-optic light guide Bulb :
62.	eye		Reflector type halogen bulb 15V 150W (24V 250W optional) Illumination
	eye
			field : 48 mm (Ø) Light intensity : 80000 LUX max. Filter : Various filters
			are available
			Infant Warmer for Intensive Care Procedures, Includes Micro-processed
			Temperature Control and Orientable Halogen Examination Lamp, with
			Lateral Movement Allowing Free Access for X-Ray.
			Crib of Wide Dimensions 55×65 cm approx. with Washable and Hypo-
			allergic Mattress Tray Apt for X-Rays.
			Lateral Panels Foldable up to 180º, with Four back IV Ports.
			Trendelenburg and Fowler Movement of ±15º minimum
			Displays:
			Digital Skin Temperature Thermometer
			Resolution ≥ 0.1ºC, Range minimum 20 to 42 ºC
			Temperature Accuracy ±0.3ºC or better
			Digital Set Point, Resolution 0.1 ºC, Controllable Range minimum 34 ºC to
			38 ºC
			Heater Power Indicator
			Skin or Manual Control Mode Indicator
			Performance
			-Continuous Circuit Monitoring
			-Self-calibrating Temperature Circuits
			-Automatic default Set-point of 36 ºC for Skin Temperature and
			Memory for Control Temperature
63.	Infant reanimation centre		-Memory for Control Set-point Short Term Energy Failure
			-Interchangeable Skin Temperature Probes: ±0.1ºC
			Alarms
			Skin Temperature ±1ºC
			Patient Alarm: Heater Remains at max. Power for more than 15
			Consecutive minutes.
			Skin Temperature Sensor Failure.
			Electronic Circuit Failure
			Power Failure
			Alarm Reset and other
			Accessories:
			Skin Temperature Sensor
			Lateral Rail for Accessories
			IV Pole
			X-Ray Cassette Tray
			Patient Identification Card Holder
			Monitor Shelf
			Auxiliary Connection Box
			Holder for Puls-Oximeter
			Puls-Oximeter for Infants
			Lateral Handles for Moving and Instruction Manual

page 25 of 27

		Equipment & Furniture Component

			Phototherapy Lamp
			Resuscitation System
			Power requirements
			220 VAC ±10 % , ≤50W, 50Hz.
			Twins monitoring capability
			External ultrasound transducers for measurement of foetal heart rate
			Detection of foetal heart echo by autocorrelation
			Foetal heart rate tange at least 50–210 /min
64	Cardiotocograph		Alarms for high and low foetal heart rate
			External displacement transducer for measurement of uterine activity
			Digital and graphical display of foetal heart rates and unterine activity
			Two channel recorder with event marker and annotation capability
			Power requirement 220 V, 50 Hz
			Nebulizer with compressor on mobile stand
			Aerosol particles in range 1 to 5 micron
65	Nebulizer		Flow rate at least 4 ml/minute
			Liquid/medication container at least 200ml
			Power requirement 220 V, 50 Hz
			High frequency generator
			kV range at least 22–35 kV with 1 kV increments
			mA range up to at least 100 mA
			Time range at least 0.05–86sec
			mAs range at least 5–500 mAs
			Automatic exposure control
			X-ray Tube
66.	Mammograph		rotating anode
			heat capacity at least 300,000 HU
			heat dissipation rate at least 60,000 HU/min
			target/filter Mo/Mo, Mo/Rh
			dual focus 0.1/0.3 mm
			Breast compression system with automatic, manual and fine adjustment
			Grid ratio 5:1
			Radiation shield with lead glass as required
			Single plane angiography system
			4-way table top motion
			Collision prevention system
			X-ray Generator
			high frequency
			100 kW @ 100 kVp
			radiographic mA up to 1000 mA
			radiographic kVp 60–150 kVp
			radiographic timer up to 1.5 sec
			fluoroscopic mA up to 10 mA
			fluoroscopic kVp 60–110 kVp
			pulsed fluoroscopy
			cine range up to at least 30 f/sec
	Coronarography/Angiogr		X-ray tube
67.	Coronarography/Angiogr		80 kW
67.	aphy system		80 kW
	aphy system		heat storage capacity at least 1,500 kHU
			heat storage capacity at least 1,500 kHU
			heat dissipation rate at least 300 kHU/min
			dual focus, focal spot size 0.6/1.2 mm or less
			grid pulsed and cooled
			Digital dynamic flat detector
			23 cm with zoom fields
			Storage capacity at least 50,000 images at 1,024 × 1,024
			At least two 17 inch monitors
			Digital subtraction angiography
			Cardiac analysis software package
			Other software packages to suit user applications
			DICOM 3 compatibility
			Radiation shield as required
			Contrast injector

page 26 of 27

		Equipment & Furniture Component

			Monitoring system
			Accessories as specified by user
			Room preparation as required by user
			Convertible into operating table for emergency Caesarian section
			Adjustable backrest
			Removable headboard
			Leg supports
68.	Delivery Couch		Removable foot section
			Height adjustable over at least 60-90 cm
			With castors at least 12 cm dia, at least two diagonally lockable
			Corner bumpers
			Removable drain pan
			Heat control
			manual or automatic
			range includes 34–37 °C
			heater indicator
			Temperature display
			set point temperature
69	Infant warmer		skin temperature
			range includes 30–39 °C
			Alarms
			audiovisual
			sensor disconnect
			power failure
			Power requirement 220 V, 50 Hz
			Capacity at least 50 kg/cycle
			Cylinder volume at least 500 litre
			Stainless steel construction of parts exposed to corrosion
70.	Washing machine		Electric heating
			Adjustable extraction speed including 300–500 rpm
			Multiple liquid supply and detergent connections
			Programmable

page 27 of 27